NACE-CIP2-001 Free Exam Study Guide! (Updated 100 Questions)
NACE-CIP2-001 Dumps for CIP Level 2 Certified Exam Questions & Answer
NEW QUESTION 15
Surface preparation of concrete is performed using:
- A. Methods that are exactly the same as steel
- B. Methods that have been modified for concrete
- C. Methods that are the same as wood
- D. Methods that are completely different to steel
Answer: B
NEW QUESTION 16
You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value.
As this is not part of the standard you should:
- A. Ignore the additional requirement
- B. Request clarification from the specifier
- C. Enforce the additional requirement
- D. Call your supervisor
Answer: C
NEW QUESTION 17
Which product, is used in conjunction with other coatings such as FBE when the lines run through wetlands or a body of water?
- A. Coal Tar Enamel
- B. 3-Layet Polyethylene (PE)
- C. 2-Layet Polyethylene (PE)
- D. Concrete
Answer: D
NEW QUESTION 18
The number of air turns in an enclosure can be affected by all of these EXCEPT
- A. type of dehumidification equipment (refrigerant or desiccant).
- B. coating type.
- C. manufacturer of the equipment.
- D. time of the year (winter/summer).
Answer: B
NEW QUESTION 19
When ASIN D 3363 is specified the Inspector must:
- A. Record the percentage of failure
- B. Use the correct solvent
- C. Record the highest value attained
- D. Record the two end points identified in the standard
Answer: D
NEW QUESTION 20
You are a NACE Level 2 in-house inspector working in a shop. Your in-house requires you to perform a sleeve test to test for soluble salts; however the 3 rd party NACE Level 3 inspector, the owner, has a san smart meter and has achieved a very different result and has rejected the pre-cleaning.
Your FIRST course of action is to:
- A. Advise the other inspector he is using an incorrect method
- B. Advise your QC Manager to change the ITP to the use of the salt smart meter
- C. Redo the pre-cleaning based on the other inspectors results
- D. Review the specification with the other inspector to see what method was specified
Answer: D
NEW QUESTION 21
When observing design defects the NACE Inspector should:
- A. Ignore the defect as the inspector can't change the design
- B. Stop the job immediately
- C. Request that the item be rebuilt with a better design for coating
- D. Document the defect and the potential problems that could result
Answer: D
NEW QUESTION 22
Thermal Spray coatings provide:
- A. Thermal protection
- B. Barrier protection
- C. Sacrificial protection
- D. Inhibitive protection
Answer: C
NEW QUESTION 23
NACE No.13/ SSPC 6 identifies the use of:
- A. Watterjetting only
- B. Steam cleaning only
- C. Various methods of cleaning
- D. Abrasive blasting only
Answer: C
NEW QUESTION 24
All of these are advantages of using repair patches EXCEPT
- A. excellent abrasion resistance.
- B. special tools or equipment are required.
- C. barrier to moisture and corrosion.
- D. inert to common acids, alkalis, and solvents.
Answer: B
NEW QUESTION 25
When using a destructive Paint Inspection Gauge the NACE inspector must:
- A. Determine the Dry Film Thickness of the coating prior to use
- B. Ensure the glue on the dolly is properly applied prior to use
- C. Consult SSPC Guide 1 prior to use
- D. Select the appropriate hand wheel based on the measured Dry Film Thickness prior to us
Answer: A
NEW QUESTION 26
WJ-1 is always performed using UHWJ at pressures above 210 MPa (30,000 PSI)
- A. False
- B. True
Answer: B
NEW QUESTION 27
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Stop the job
- B. Advise the Owner and write a Non-Conformance report
- C. Ignore the situation
- D. Require the Applicator to remove the coating
Answer: D
NEW QUESTION 28
Measuring methyl ethyl ketone (MEK) resistance of ethyl silicate inorganic zinc-rich primers by solvent rub requires
- A. 50 double rubs with a saturated cloth.
- B. 25 double rubs with a saturated cloth.
- C. 35 single rubs with a saturated cloth.
- D. 25 single rubs with a saturated cloth.
Answer: A
NEW QUESTION 29
Surface preparation methods for Non-ferrous metals are:
- A. Not required
- B. The same as for Ferrous metals
- C. Specific for each type of Non-ferrous metal
- D. The same for all Non-FetT0us metals
Answer: C
NEW QUESTION 30
......
Use Real NACE-CIP2-001 Dumps - 100% Free NACE-CIP2-001 Exam Dumps: https://www.testkingpass.com/NACE-CIP2-001-testking-dumps.html
Realistic Verified NACE-CIP2-001 exam dumps Q&As - NACE-CIP2-001 Free Update : https://drive.google.com/open?id=1Nv6ly6xkCKLqtRrPQEQDLuFe7ySsUyQ3