API-570 Dumps PDF New [2023] Ultimate Study Guide
API-570 Exam Dumps PDF Updated Dump from TestkingPass Guaranteed Success
API 570 certification exam covers a range of topics including inspection techniques, welding procedures, damage mechanisms, corrosion, and material properties. It also assesses the candidate's ability to interpret and apply industry codes and standards such as the ASME B31.3 Code for Process Piping, the API 570 Piping Inspection Code, and the API RP 574 Inspection of Piping, Valves, and Fittings. API-570 exam is divided into two parts, a closed-book part that tests the candidate's knowledge of the codes and standards, and an open-book part that requires the candidate to apply their knowledge to practical scenarios.
NEW QUESTION # 12
What should have been the correct number and type of guide bends on the PQR?
- A. 1 side, 1 face and 1 root bend
- B. 2 face and 2 root bends
- C. No side bends required
- D. 6 side bends
Answer: C
NEW QUESTION # 13
Determine the MAWP of the following piping system , at the next inspection, based on the following Design pressure/temperature Pipe description Outside diameter of pipe, D Thickness determined from Inspection Observed Corrosion Rate Next planned inspection 100 psig/100°F NPS 20, Sch. std, A 106 B 20"
0.280"
0.02 inches/year 5 Years
MAWP=
- A. 550 psig
- B. 723 psig
- C. 160 psig
- D. 125 psig
Answer: C
NEW QUESTION # 14
A pipe has the highest potential of resulting in an immediate emergency if a leak were to occur.
- A. Class 1
- B. Class 2
- C. Owner/user designated system
- D. Class 3
Answer: A
NEW QUESTION # 15
When may welding not be performed?
- A. If the weld area is above 120° F
- B. If the weld area is in an inert atmosphere
- C. If the weld area is frosted or wet
- D. If the weld area is not in direct sunlight
Answer: C
NEW QUESTION # 16
Where should the numbers be placed on a radiograph?
- A. On the material being radiographed
- B. On the film source pack
- C. Under the material being radiographed
- D. Under the film
Answer: A
NEW QUESTION # 17
When an injection point circuit for the purpose of inspection is designated, the recommended up stream limit of the injection point circuit shall be the greater of ?
- A. minimum 12 inches
- B. both A and C
- C. maximum 12 inches
- D. three pipe diameters
Answer: B
NEW QUESTION # 18
A WPS shall have the referenced
- A. NACE
- B. PQR
- C. PDQ
- D. welder
Answer: B
NEW QUESTION # 19
Actively engaged as an authorized piping inspector shall be defined as a minimum of time spent performing inspection activities.
- A. 20%
- B. 30%
- C. 40%
- D. 50%
Answer: A
NEW QUESTION # 20
Determine the MAWP of the following piping system, at the next inspection, based on the following Design pressure/temperature Pipe description Outside diameter of pipe, D Thickness determined from Inspection Observed Corrosion Rate Next planned inspection 100 psig/750°F NPS 6, A285 C EFW, Straight Seam(No radiography) 6 5/8" 0.280"
0.01 inches/year 5 Years
MAWP=
- A. 487 psig
- B. 522 psig
- C. 125 psig
- D. 878 psig
Answer: B
NEW QUESTION # 21
Temperatures above can damage transducers not equipped with delay line material.
- A. 1,000 psi
- B. 280 psi
- C. manufacturer's specification
- D. There is no limit to temperature
Answer: C
NEW QUESTION # 22
What document may be used as a guide when examiners are being qualified by their employer?
- A. API 570
- B. ASM E Section V
- C. ASNT SNT- TC-1A
- D. ASME Section IX
Answer: C
NEW QUESTION # 23
An area defined by a circle having a diameter not greater than 2 inches for a line diameter not exceeding 10 inches, in which thickness readings may be averaged is
- A. Test point
- B. Averaging point
- C. WFMT
- D. TML
Answer: A
NEW QUESTION # 24
An operator notice a pipe off its support, what should be done?
- A. Contact maintenance personnel for immediate repair
- B. Keep a record of the situation for future reference
- C. Ignore the situation
- D. Report the situation to engineering or inspection personnel
Answer: D
NEW QUESTION # 25
Which of the following best describes API 574?
- A. Recommended practice
- B. Standard
- C. code
- D. specification
Answer: A
NEW QUESTION # 26
According to API 570, a(n) is a person who assists the inspector by performing specific NDE testing.
- A. NDE technician
- B. Inspector assistant
- C. Examiner
- D. Level II inspector
Answer: C
NEW QUESTION # 27
The three well-known methods of determining soil resistivity are, soil bar, soil box and______.
- A. A-C Bridge
- B. Wenner (4-pin) method
- C. six pin method
- D. holiday pipe survey
Answer: B
NEW QUESTION # 28
Which of the following applies to socket welds in piping systems?
- A. Should be welded using SAW only
- B. Should be avoided where crevice corrosion may occur
- C. Should be avoided
- D. Should be used in all welded piping
Answer: B
NEW QUESTION # 29
With respect to a Class 400, NPS 12 slip on raised face flange, whose edges of the gasket do not extend to the bolt, what is the outside diameter of the gasket?
- A. 12.75"
- B. 18.00"
- C. 16.50"
- D. 15.00"
Answer: D
NEW QUESTION # 30
......
API-570 (Piping Inspector) Certification Exam is a specialized certification offered by the American Petroleum Institute (API) to individuals who have expertise in the inspection, repair, alteration, and re-rating of in-service piping systems. Piping Inspector certification is designed for professionals who perform piping inspections in refineries, chemical plants, and other industrial facilities. The API-570 certification exam tests the knowledge and skills required to ensure the safe and reliable operation of piping systems.
Pass Your API Exam with API-570 Exam Dumps: https://www.testkingpass.com/API-570-testking-dumps.html
API-570 Exam Dumps - API Practice Test Questions: https://drive.google.com/open?id=1sA242BzgCdkppPd3svUsrDdQfMTZzmbY